![]() The best way to avoid jamming the blades when blending hard ingredients is to put the harder ingredients into the cup first, which means they will be at the top when the cup is turned upside down and placed on to the base. To check whether the blades are jammed, switch the NutriBullet off, unplug it, remove all ingredients and check the blades closely to make sure they are rotating freely. Most blenders have a hard time blending fruit without liquid so you might just need to add more! Try checking out our list of NutriBullet weight loss smoothies if you need some good ideas! With harder ingredients, this problem can occur even if the cup is not filled to maximum. If you are attempting to blend hard ingredients but your NutriBullet’s blades are not spinning, the problem could be that the ingredients have jammed the blades. To avoid this issue, only ever fill your cup up to the MAX line, or ideally a little bit less. The reason for this is that your NutriBullet needs space around its blades in order to move the ingredients freely around the cup and blend properly without the blades getting stuck. Filling the cup beyond this line could cause the NutriBullet to stop working. Your NutriBullet cup has a line that shows the maximum level it should be filled to. If you need to use your NutriBullet urgently, then removing the cup and blowing cool air toward the motor using a hair dryer on a cold air setting may help it to cool down more quickly. Once the temperature of the motor has returned to a safe level, the blender will switch on again as normal. It will take some time for the motor to cool down, so the best thing to do in this situation is to unplug the NutriBullet and leave it switched off for an hour. Instead, it will have automatically switched itself off before it got too hot in order to avoid permanent damage. The good news is that you are unlikely to have permanently damaged the motor and it probably hasn’t switched off because it is broken. However, if your NutriBullet switches off suddenly, while you are using it – and particularly if you’ve been doing lots of blending – then an overheating motor is very likely to be the problem. If the blender hasn’t been in use, the motor should be at room temperature and well within its safe operating range. If you haven’t used your NutriBullet for some time and it doesn’t switch on then an overheating motor is unlikely to be the problem. If your NutriBullet smells like it’s burning then it’s probably overheating. Your NutriBullet motor will naturally get hot when it is in use, and this heat can build up if the motor is under heavy use for an extended period of time.Īs the motor has a safe operating temperature, excessive heat could be dangerous, so your NutriBullet has a built in system that switches off the motor when it gets too hot. If it doesn’t, then the problem must lie elsewhere. Once all three tabs can easily be pressed down, put the cup bag on to the base, twist into position, and the NutriBullet should turn on. You may also need to remove any small pieces of debris or add a little oil (cooking oil is fine) to lubricate the switches and get them moving again. If you suspect that the activators may be the reason why your NutriBullet is not starting then turn the power off, remove the cup, and gently clean the activators with warm water. If any one of these tabs gets stuck, so that it does not press down, or if you are not twisting the cup into place correctly, then the NutriBullet will not start. This system relies on three tabs, also known as ‘activators’ which need to be pressed down by the cup. Make sure you don’t put the motor base of your NutriBullet in the dishwasher! The Activators are Not Being Pressed Down CorrectlyĪ NutriBullet switches on when the cup is connected to the base and twisted into place. However, there are more possibilities too, so read on before concluding that it is a power problem. If the other appliance does switch on, but your NutriBullet doesn’t, then it could be an electrical fault. ![]() If it doesn’t, the problem isn’t with your NutriBullet. Try connecting another appliance to test whether it switches on. The obvious first step is to check that your NutriBullet is plugged in and that there are no problems with the cables or with the power outlet. If an electrical appliance doesn’t switch on, your first thought should always be that it may not have power. Some of these are user error while others might be an issue with your blender. There are 5 reasons that may explain why your NutriBullet won’t turn on. Summary: Why a NutriBullet Blender Stops Workingĥ Reasons Why Your NutriBullet Stopped Working.Hard Ingredients are Jamming the Blades.The Activators are Not Being Pressed Down Correctly.5 Reasons Why Your NutriBullet Stopped Working.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |